1. Verify and make sure the ignition is switched OFF.
2. Connect the 2 pins in the MES with a paper clip or metal object.
3. Turn the ignition switch ON.
4. The SRS Indicator Light should come on for 6 seconds and then go off.
5. The SRS Indicator Light should come back on agian.
Contents
How do you turn off the airbag light on a Honda Accord?
1. Verify and make sure the ignition is switched OFF.
2. Connect the 2 pins in the MES with a paper clip or metal object.
3. Turn the ignition switch ON.
4. The SRS Indicator Light should come on for 6 seconds and then go off.
5. The SRS Indicator Light should come back on agian.
6. The SRS light should go off.
How do you reset the airbag light on a Honda?
1. Turn IGNITION on (but don’t start car)
2. After the AIR BAG warning lamp lights for 7 seconds, turn IGNITION off within 1 second.
3. Wait 4 seconds.
4. Turn IGNITION on (but don’t start car)
5. After the AIR BAG warning lamp lights for 7 seconds, turn IGNITION off within 1 second.
How do you turn the SRS light off?
How do you reset the SRS light on a 2001 Honda Accord?
1. Verify and make sure the ignition is switched OFF.
2. Connect the 2 pins in the MES with a paper clip or metal object.
3. Turn the ignition switch ON.
4. The SRS Indicator Light should come on for 6 seconds and then go off.
5. The SRS Indicator Light should come back on agian.
How do you reset the SRS light on a 1998 Honda Accord?
Can you reset airbag light without tool?
How to reset airbag light without a Scanner. In some older cars, though, it is possible to reset the airbag light without a scanner by removing the car battery terminals. Check the wiring system underneath the driver or passenger seat for any loose wires or corrosion in the connector plug.8 jui. 2021
What does SRS light mean on Honda Accord?
The SRS, or supplemental restraint system, on your Honda Accord is responsible for deploying the airbag in the event of an accident. If this system is malfunctioning, the airbag may not deploy properly during an accident. … The yellow “SRS” light on the dash will light up, indicating a problem with the system.
Why did my SRS light came on?
If your airbag light is on, it could also indicate a problem with your seat belts. Your airbag or SRS light might also come on if your vehicle was in an accident that activated the crash sensors in your car, but not to the point where the airbag deployed. In this case, you need to have your airbag reset.29 déc. 2015
Where is the fuse for SRS light?
The fuse block is on the driver’s side of the engine compartment. Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block. Turn the ignition switch to “ON” without starting the engine.12 jui. 2017
How does Honda diagnose SRS light?
If your Honda airbag light remains on, it most likely means that the Supplemental Restraint System (SRS) has detected a problem with the airbag system. When your Honda airbag system functions properly, the airbag light comes on when you turn on the ignition but should turn off once you start the engine.31 déc. 2020
Why is my SRS light on in my Honda Civic?
This light indicates that a fault has been detected and the airbags may not deploy or deploy properly in an accident. The SRS warning stands for Supplemental Restraint System. It supplements the primary restraint system, the seatbelts.
Where do you reset the airbag light?
1. Put the key into the ignition and turn the switch to the “on” position.
2. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
3. Repeat Steps 1 and 2 two more times.
How do I fix my SRS light on my Mitsubishi?
1. Plug the Mitsubishi airbag scanner into the OBD2 port under the dashboard, driver’s side.
2. Turn on the ignition and allow the scanner to power on.
3. Select your Mitsubishi model and year.
4. Select SRS / Airbag Control unit from the main menu.
5. Select Read Fault Codes.
Will disconnecting the battery reset the airbag light?
Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. … Remove the terminal clamp and leave it disconnected for 5-10 seconds to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.10 avr. 2020