That’s why I run a 4.56 gear ratio with 35″ tires. This gives me decent fuel efficiency at highway speeds, and enough low end power to throttle through difficult obstacles.
Also know, what gear ratio do I need for 35 inch tires Jeep Wrangler? In most applications, with normal driving habits, you’ll usually want to back up the 35-inch tires with 4.88 gears.
People ask also, what gears for Jeep with 35s? What gears do I need to run 35s? If it’s an automatic, you’ll ideally want 4.56 gears. 4.10 isn’t bad at all on the highway with 35s, but 4.56 is perfect. You’ll be a wee bit lower RPM with the auto.
Also, are 4.10 gears good for 35s? 4.10 will be just fine for 35’s and Especially if you get a 4:1 transfer case for off road adventures. I recently went from 3.21 to 4.10 with 35″ Terra Grapplers. It made a huge difference on my 2dr with manual transmission, It’s just about perfect around town. I run at about 2400rpm at 70 in 6th gear now.
Likewise, are 4.10 gears good for highway? Installing 4.10 gears improves the car’s performance on the track but with negligible effects to the highway driving. If your car is equipped with an overdrive, you may not even notice a difference in gas mileage with the new higher gearing.
Contents
Can 3.73 gears handle 35s?
You can do it but it’s definitely not ideal. The ratios with a 5.13 first on a 3.73 rear end and 35’s (your proposed setup) is very slightly taller than what a stock 6MT Tacoma is in first gear so it’s not like you’re going to be causing massive wear getting started.
What is the best gear ratio for 33 in tires?
While 4.56 is ideal for 33″ tires and 5-speed transmission, the 3-speed auto’s lack of an verdrive makes 4.10 the best all-around street and offroad ratio. The only time you’d want 4.56 with 33″ tires and 3-speed automatic is if your engine was the 2.5L four-banger.
Why do you Regear a Jeep?
Regearing refers to the process of changing your pinion gears and ring gears to a different ratio, which changes the balance of torque and speed. Regearing your Jeep is a crucial step in adjusting the size of your tires since improper gearing can result in more stress being transferred to the axle.
Are 4.56 gears good for 35s?
You will be fine, your RPMs may be above 3K at about 65 mph. Yea thats what I have been trying to say. So running 4.56’s how bad will 35’s be just going around town. I rarely go over 60mph an if I do its one exit like 2 miles on highway..
Are 4.88 gears good?
4.88 are great… but you’ll be reving it out on the freeway just to stay at speed. 4.56 are more “well rounded.”
Do I need to Regear 35s JK?
285/70-17 is 102.8″ in circumference. 315/70-17 is 108″ in circumference. So we know that the 35″ tire is 5% larger in circumference and to maintain stock performance, we need a gearset that is 5% lower. So to maintain stock performance with a 35″ tire, a 4.30 gear is needed.
Is a 4.10 gear ratio good?
FACT: A 4.10 axle ratio is ideal for towing heavy loads in a mix of city and highway driving and when towing on varied or steep grades. A 4.10 axle ratio will provide improved acceleration in stop and go city traffic.
Will gears make my truck faster?
The simple answer is yes. More aggressive gearing creates a quicker car but not a faster car. … If you swap in taller rear gears, you can gain some top-end speed, making your car faster, but you’re going to be a bit slower leaving from a stop. You’ll get an opposite result when you swap in shorter gears.
What is the best gear ratio for a Jeep Wrangler?
In many cases, 5.13 is recommended above for 35s, when 5.38 would actually be a better choice. However, unless you have a Rubicon model (that has both a Dana 44 front and rear axle), then you will have no choice but to use 5.13 gears, unless of course you swapped in Rubicon axles.
Is 3.42 or 3.73 better?
The 3.42 is fine for towing smaller boats, plus you will get better gas mileage for everyday driving. If I were towing frequently on hilly roads, I might would go for the 3.73 for better gas mileage while towing, but the 3.42 should be fine with a 205.