Insert the key into the ignition to do this, turn the car on for about a second, then off for about a second. Do this two times more then drive the car as normal. This can be done by putting the car on and back off three times in quick succession.
Likewise, how do you turn off the check engine light on a 2011 Ford Explorer?
- Let it go off by itself.
- Turn your ignition on and off several times in a row.
- Disconnect your battery and reconnect it.
- Buy an OBD II scanner (they’re relatively inexpensive) and follow the instructions (it’s pretty easy)
People ask also, how do I turn my check engine light off?
Also, how do you reset the check engine light on a 2011?
- Turn off the ignition and put on safety glasses and gloves.
- Locate the negative terminal on your car battery.
- Loosen the nut on the negative terminal with a wrench and pull the negative connector from the battery.
- Reconnect the negative cable and tighten it with your wrench.
Also know, can I reset my own check engine light? Turning the Ignition On and Off The on-off method is the equivalent fix for a vehicle’s check engine light. It forces the computer to refresh its saved state through a reboot. Simply place your key into the ignition and turn it on for 1-2 seconds, then turn it off for 1-2 seconds. Repeat this step three or four times.Did you know that you can get your check engine light scanned for free? Any of the major parts stores in the country, such as: Napa, Advance Auto, Autozone and O’Reilly’s, will scan your vehicle, and tell you the P codes for no charge at all.
How do I reset my check engine light without a scanner?
Why is my check engine light off but code still there?
The problem that triggered the code may not have happened enough times to illuminate the light. This most likely means the issue is not critical and that the code is pending. So if the check engine light is off, but you see an error code, use an OBD2 scanner to help identify what the problem is.
How do you reset the check engine light on a code reader?
Press the “erase/clear” button on your scanner, then turn off the key and disconnect it. Clearing any codes present will turn off your check engine light temporarily. After pressing “erase/clear” and waiting until you see a “no codes” message, you can turn off your vehicle and disconnect the scanner.
How far do you have to drive to reset the check engine light?
To make sure the check engine light does not reappear, it’s recommended that you drive your car 30 to 100 miles. This enables the vehicle’s “Drive Cycle” to reset, as the various sensors need time to recalibrate.
What is the most common reason for check engine light?
Replacing a faulty oxygen sensor — a sensor used to optimize a vehicle’s fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.
How do I permanently delete engine codes?
The only way to clear a PDTC is to fix the underlying problem with the vehicle that originally caused the PDTC and its corresponding DTC to set, and then allow the vehicle sufficient drive time to re-run the monitor that identified the problem in the first place.
How do you reset the check engine light on a 2011 Chevy Cruze?
If You’ve fixed the basic cause of the light illuminating, such as a loose gas cap, You can simply put the key in the ignition, and crank the engine. Once Your vehicle has started, turn it back off. Now, repeat turning Your car engine on and off two more times.
How do you tell if OBD codes have been cleared?
If the vehicle does not support the above datapoints you can use the smog check feature to check for indications of codes being recently cleared. When codes are cleared all vehicle emissions tests are reset and will display a status of ‘not complete’.
How many miles do you have to drive to reset oxygen sensor?
Here’s something you probably don’t know: after clearing the car’s computer you will need to drive for about 50 to 100 miles. As you drive your car the computer will monitor all the sensors and register the results.
Can bad gas cause a check engine light?
Sometimes a tank of bad gas can cause a “check engine” light to come on. If your indicator light is caused by bad gas, it will shut itself back off after you run a tank or two of good gas through the car. Bring the car in to have the code read.