Beside above, how do you reset the change oil light on a 2003 Ford Explorer?
- Press “SETUP” to access the System Check function.
- Press and release “RESET” to display “OIL LIFE XX%”.
- Press and hold “RESET” for 2 seconds to display “IF NEW OIL HOLD RESET”.
- Press and hold “RESET” to display “OIL LIFE SET TO 100%”.
People ask also, where is the oil stick on a 2003 Ford Explorer? Locate the Dipstick On most models, the dipstick is located on the left side of the engine. The dipstick usually has a yellow or orange circular handle that is clearly visible. When you pull this handle, a long piece of metal will slide out of the engine.
Moreover, what type of oil does a 2003 Ford Explorer use? Ford Explorer 2003, SAE 5W-30 Synthetic Blend Motor Oil, by Motorcraft®.
Also the question is, can 5W30 be used instead of 5W20? Can You Use 5W-30 Instead of 5W-20? In theory, yes, you can switch from using 5W-20 to the 5W-30 because they have similar viscosity ratings. In fact, often, when you take your car to a mechanic for an oil change, they’ll put the 30 instead of the 20 because it’s thicker.
- Crank the Explorer’s engine or turn the key to the “ACC” ignition position. Push the “Setup” button to the right of the steering wheel.
- Push “Reset.” The screen will show “Oil Life – Hold Reset New”
- Press and hold “Reset” for two seconds.
Contents
How do I reset my Ford Explorer?
- Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
- Disconnect the negative battery terminal.
- Wrap the negative clamp in a towel.
- Leave the negative battery cable off for a minimum of five minutes.
How do you reset the service engine soon light on a 2002 Ford Explorer?
Explorer Addict Just unhook the negative terminal for a few minutes and it should reset. OBDII resets the light anyway once the problem is gone, so if you think you’ve fixed the problem and the light is still on its prob. still there. The code will be stored in the computer but the light should be gone.
How much oil is too much on the dipstick?
In most vehicles, the dipstick will have low and high marks that indicate the oil level. If the excess oil is just 1-2 millimeters above the fill line, this shouldn’t be cause for concern. However, if there’s a quart or more of extra oil in the engine, it’s best to remove it.
Why is there so much oil on my dipstick?
In certain cases, the oil level may have risen since the last time you checked or there is too much oil on the dipstick. This could be due to condensed water (from combustion), condensed fuel or a coolant leak – all are causes for concern. … Free and emulsified water is harmful to the oil and the engine.
Can I drive my car with too much oil in it?
If you have put too much oil in your car, you should drain the excess oil. If you’re not confident doing this, you will need to get your vehicle towed to a mechanic – driving it could damage the engine, requiring expensive repairs. … Refill your oil reservoir to below the maximum level if you have over drained.
What type of oil does a Ford Explorer use?
SAE 5W-30 Full Synthetic Motor Oil by Motorcraft®.
What kind of oil should I use in my 2002 Ford Explorer?
The two base engines the 4.0L V6 (non-flex fuel compatible) and the 4.0L V6 (flex fuel compatible) require 5 quarts of 5W30 synthetic oil while the 4.6L V8 optional engine takes 6 quarts of 5W20 synthetic oil.
How much oil does a 2002 Ford Explorer take?
Capacity: 6 quarts (with filter)When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase. After refill, check oil level.
What happens if you mix 5w30 and 5W-20?
You can’t mix between regular/synthetic blend/full synthetic but mixing weights, especially if they’re by the same manufacturer, is no problem.
What happens if you put 5W-20 in a 5w30 car?
What Actually Happens When You Mix 5W30 with 5W20? Nothing serious is going to happen. The oils will come together, but they are unlikely to blend into a single oil; so, they’d stay and flow separately.