To reset the oil level warning or maintenance light in your 2012 ford explorer vehicle, turn the ignition key to the “on” position and depress the gas pedal slowly three times. Release and start your vehicle and oil light should indicate a reset.
Also know, how do you reset the oil life on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.
Likewise, how do you reset the oil life on a 2011 Ford Explorer? To reset the ford explorer oil life light, put the ignition into on without starting engine. Use the pad on the steering wheel to scroll through the settings. Go to settings, vehicle, oil life reset. Push and hold ok.
People ask also, how do you reset the oil life on a 2013 Ford Explorer?
Also, why is my change oil light on when I just changed my oil? The light could be on after an oil change because of an issue with the oil pump. If this is the cause, there could be not enough oil circulating through to the various parts. Performing regular oil changes should help prevent this from happening, but parts do wear out.
- Get in the car and turn key to the on position.
- Go to the SETUP MENU HOLD RESET screen.
- Press and hold the SELECT/RESET button.
- Enter to the RESET FOR SYSTEM CHECK menu.
- Scroll to OIL LIFE.
- Hold down the SELECT/RESET button.
Contents
How much oil does a 2011 Explorer take?
Capacity: 6 quarts (with filter)After refill check oil level.
How do you reset the oil life on a 2015 Ford Explorer?
How do you reset the oil life on a 2014 Ford Explorer?
How do you reset after oil change?
Insert the key into the ignition and turn it to the “on” position without starting the engine. Depress the gas pedal slowly three successive times within 10 seconds. At this point, the system should have reset. You can verify by turning the ignition off and then on again.
Do you have to reset oil life after oil change?
Do not reset the oil light unless you have actually changed the oil. The light is there to tell you when it’s time to change the oil. Resetting the light without changing the oil may cause you to miss an oil change, which can damage your engine.
What are the signs of a bad oil pump?
- Low Oil Pressure.
- Increased Engine Temperature.
- Hydraulic Lifter Noise.
- Noise from the Valve-Train System.
- Noise at the Oil Pump.
- Stop Driving.
- Check the Oil Pressure Measurement Unit on the Engine.
- Check the Engine Oil Port Pressure Using A Gauge.
How do you reset the oil life on a 2010 Ford Sport Trac?
- Turn the ignition to run (one position before starting engine).
- Press SETUP to display OIL LIFE %.
- Press RESET button to display “HOLD RESET IF NEW OIL”.
- Press and hold the RESET button for more than two seconds.
What does the wrench light mean on a 2010 Ford Explorer?
If You see the wrench light turn on in the dash of Your 2010 Ford Explorer this means that Your ECU has detected a fault. I recommend getting off the road as soon as possible because continuing to drive can cause more damage to Your SUV.
What type of oil does a 2011 Ford Explorer use?
The approved oil type for the 2011 Ford Explorer 4.6L and 4.0L is the SAE 5W-20 and 5W-30 displaying the API Certification Seal. The engine oil capacity for the 2011 Ford Explorer is 6 and 5 US quarts.
Can 5W30 be used instead of 5w20?
Can You Use 5W-30 Instead of 5W-20? In theory, yes, you can switch from using 5W-20 to the 5W-30 because they have similar viscosity ratings. In fact, often, when you take your car to a mechanic for an oil change, they’ll put the 30 instead of the 20 because it’s thicker.