Wait 1 minute for the Range Rover‘s electronic control module to cycle and reset. Then, reconnect the clamp to the negative battery terminal. Tighten the retaining nut on the cable clamp. The airbag light should go out at this point.
Also, how do I clear the air bag warning light?
- Put the key into the ignition and turn the switch to the “on” position.
- Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
- Repeat Steps 1 and 2 two more times.
Another frequent question is, what does it mean when your airbag light comes on and stays on? The airbag light indicates that something is wrong with the seatbelts or airbags. This means that it’s probably not safe to drive with the airbag light on. If it stays illuminated in your vehicle, we recommend having it towed to the dealership rather than driving it yourself.
Likewise, will disconnecting battery reset airbag light? Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. … Remove the terminal clamp and leave it disconnected for 5-10 seconds to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.
Furthermore, how much does it cost to reset the airbag light? Number 1 — Reset Airbag Light You’ll need to hire a professional to come in and examine the airbags before you continue to drive the car. This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.If the airbag light is on, it means that the airbag will not be able to deploy in the event of an accident. This is a dangerous proposition, and it means that you should avoid driving if at all possible in that vehicle.
Can a blown fuse cause the airbag light to come on?
Blown fuses can definitely cause the airbag light to come on. When the airbag system is malfunctioning, a mechanic or auto parts store should be able to read the code that the system is putting out which will give them a clue as to what particular problem the airbag is having.
Can you unplug an airbag sensor?
Disconnecting the airbag unit from the harness without unplugging the battery may trigger the airbags to deploy or may cause damage to the computer system. After disconnecting the positive battery cable, you should wait three minutes before removing the computer module.
Can I remove airbag without disconnecting the battery?
You disconnect the battery before pulling the bag so an SRS fault isn’t stored. Airbag deployment doesn’t enter the picture at all. You could tap the front bumper against a pole or something at, say, 10-15 mph. That should get rid of the pesky airbag for you.
What happens if I remove the airbag fuse?
Every vehicle I’ve worked on has had an airbag fuse you can remove from the fuse panel to fully disable the airbag; the repair manuals recommend pulling this fuse when doing any work in the dash area since there’s some risk of triggering the airbags to go off while you’re working, which could result in serious injury …
Can low battery cause airbag light?
A bad battery will affect he voltage regulator and alternator. The alternator is now working harder to charge something that can’t be charged. This will cause other electrical problems throughout the car, which may include your airbag sensors. A bad airbag sensor will cause your airbag light to turn on.
Is a airbag warning light an MOT failure?
If your car’s airbag warning light is on during your MOT, you will need to schedule a second visit. In fact, this indicator light is considered a major reason to fail your MOT, since it directly impacts your safety.
How do I know if my airbag sensor is bad?
Symptoms of a failing airbag sensor You can easily tell if the sensor is functioning if the airbag warning light on the dashboard is illuminating every time you start the vehicle. But, if the airbag warning light stays illuminated after starting the vehicle, this is an indication of an airbag sensor problem.
How do you turn airbags off?
But the passenger airbag can be deactivated if the car is equipped with a Passenger Airbag Cut Off Switch (PACOS). In most cases, to disable the airbag you need to have the ignition switched off to avoid any possible malfunctions. The PACOS is usually located in the passenger side of the dash board.
How do you disable airbag sensor?
- Turn on the ignition switch with your car key.
- Wait for the airbag warning light to turn off.
- Turn the ignition switch of your car back off for a little longer than three seconds.
- Repeat steps 1 through 3 twice to make three times total.