To reset the 2017 hyundai elantra tpms, press the tpms reset button and keep it until the light flashes three times, and then release it. Start the car and let the sensor run for 20 minutes. Typically, you can consider the tire pressure control reset button under the steering wheel.
Contents
To reset the tire pressure monitor or tpms system in your 2017 hyundai elantra vehicle, turn the ignition key to the “on” position and depress the tpms button, usually located under the dash, until the tpms light blinks several times.
How do you reset the tire pressure sensor on a Hyundai Elantra?
First, turn the ignition to the “ON” position without starting the vehicle. Now, press the “TPMS Reset” button (which is found beneath the steering wheel) until You see the tire pressure light blink three times and then release the button. Start the vehicle and wait for at least 20 minutes for the sensors to refresh.
To reset the tpms on the 2016 hyundai elantra make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and wait ten minutes. In some cases you may need to hold the button down till the light flashes.
How do I clear the tire pressure light?
Hold the TPMS reset button until the tire pressure light blinks three times, then release it. Start the car and wait 20 minutes for the sensor to refresh. The TPMS reset button is usually located beneath the steering wheel. If you are unable to find it, refer to your vehicle’s owner’s manual.
First, locate the reset button which can be found on the left hand side of the vehicle, underneath the dashboard. Push and hold the button until the low tire pressure light flashes on and off three times.
Where is the tire pressure on a 2017 Hyundai Elantra?
To reset the tpms on the 2017 hyundai sonata make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and wait ten minutes. In some cases you may need to hold the button down till the light flashes.
Why is my tire pressure light still on after filling tires Hyundai?
If your TPMS light remains on after inflating the tires to the proper pressure, try these steps: Drive the car at 50 mph for about 10 minutes. This should reset the sensor, and the next time you start the car the TPMS light should be off. Without starting the car, turn the key to the “On” position.
Why is my tire pressure light still on after filling tires?
If you’ve added air but the air pressure warning light stays on, there’s a problem with your Tire Pressure Monitoring System or you have a slow leak. … Quick Tip: If the TPMS warning light comes back on after you’ve filled the tire with air, recheck the tire to make sure it is inflated to the proper air pressure.
How do you reset the tire pressure light on a Hyundai Elantra 2018?
The 2018 Hyundai Elantra TPMS button is placed under the steering wheel. To reset the sensor, holding the tire pressure indicator button until the TPMS light flashes three times, and then release it. Start the car and let the sensor reload for 20 minutes.
Why won’t my low tire pressure light go off?
What if corrected the tire pressure and my tire pressure light still won’t turn off? … When the TPMS warning light comes ON and stays ON, this indicates a low tire pressure condition in one or more tires. Inflating the tire to the recommended tire pressure found on the door placard should cause the light to turn OFF.
Why wont my tire pressure light go off?
If you’ve inflated your tires to the proper air pressure, but the warning light stays on, you may have a leak or there’s a problem with the TPMS in one or more of your tires. It’s simple enough to check if there’s a leak in a tire. Just use your tire gauge to recheck the air pressure in all your tires.
TPMS stands for Tire Pressure Monitoring System. In most vehicles the TPMS reset button is found beneath the steering wheel. After changing the tires on your vehicle, the TPMS needs to be electronically reset in order to clear the error code. … Start your vehicle and wait 20 minutes and the sensor will refresh.