To reset the check engine light in your 2017 hyundai elantra vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.
Contents
How do you reset the check engine light on a Hyundai?
Can I reset my own check engine light?
Turning the Ignition On and Off The on-off method is the equivalent fix for a vehicle’s check engine light. It forces the computer to refresh its saved state through a reboot. Simply place your key into the ignition and turn it on for 1-2 seconds, then turn it off for 1-2 seconds. Repeat this step three or four times.
How do I turn my check engine light off?
Why is my check engine light on in my Hyundai Elantra?
Why is the Check Engine light on in my Hyundai? … Your check engine light can signal different problems. It could mean a loose or missing gas cap, faulty oxygen sensor, under performing catalytic converter, faulty mass air-flow sensor or misfire in a cylinder.
How do I clear my check engine light without a scanner?
How do I reset my car without disconnecting the battery?
- 3.1 Step 1: Open the hood and disconnect the battery.
- 3.2 Step 2: Locate the car’s fuse box and remove the fuse.
- 3.3 Step 3: Reinstall the fuse and reconnect the battery terminal.
- 3.4 Step 4: Start the vehicle and perform a test run.
How do you reset the check engine light on a Hyundai Elantra?
To reset the check engine light in your 2017 hyundai elantra vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.
How do you reset the check engine light with a gas pedal?
Fully depress the accelerator pedal and keep it for more than 10 seconds. Fully release the accelerator pedal (The CEL light will continue to blink). Turn ignition switch to On position and now you can start the car. The CEL light should be gone.
Can Autozone reset check engine light?
Wondering if the local Autozone can turn off a check engine light? The answer is yes, but… there are a couple things to remember: Local auto parts stores will typically offer to read your codes for free, but not all locations will clear the light due to liability issues.
What is the most common reason for check engine light?
Replacing a faulty oxygen sensor — a sensor used to optimize a vehicle’s fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.
Is it safe to drive with check engine light on?
The rule of thumb is that if the check engine light is flashing, you can’t keep driving the car. It’s an emergency. Often it indicates an engine misfire. If you keep driving, you will likely cause irreversible damage, mostly to the (expensive) catalytic converter.
Why is my check engine light on in my 2016 Hyundai Sonata?
2016 Hyundai Sonata Check Engine Light Flashing Divergent handy reasons for a Check Engine Light are dirty mass airflow sensor, a malfunction with the fuel injection system, faulty emissions control part, faulty head gasket, damaged oxygen sensor, or defective spark plugs to name a few.
Can you reset a check engine light by disconnecting the battery?
Leaving the battery disconnected for about 15 minutes will ensure the vehicle systems will completely reset when you reconnect the battery. Secure the negative cable back to the terminal and cover it with the cap (if applicable). Disconnecting the battery will clear the error codes and reset the check engine light.
Will disconnecting battery reset OBD2?
But simply disconnecting the battery will not get rid of OBD2 fault codes. The ECU will still be able to store the trouble codes using power from a capacitor. In order to reset the codes, the built-in capacitor in the ECU will need to be drained of power as well.
How do you reset the check engine light after an oil change?
Insert the key into the ignition and turn it to the “on” position without starting the engine. Depress the gas pedal slowly three successive times within 10 seconds. At this point, the system should have reset. You can verify by turning the ignition off and then on again.