The 2007 Chevy Malibu axle nut size iS36 mm.
Contents
What size is the axle nut on a 2010 Chevy Impala?
The axle nut in a 2010 Chevy Impala takes a 34 mm socket to remove it. The axle nut is what holds the hub to the axle.
How much does it cost to replace a wheel bearing on a Chevy Malibu?
Chevrolet Malibu Wheel Bearings Replacement costs $304 on average. You will pay about $400, on average, for front wheel bearing replacement. The labor will be anywhere from $140-$180, while parts may cost as little as $200 or as much as $400.2 jan. 2020
How much is an axle for a Chevy Malibu?
Chevrolet Malibu CV Axle / Shaft Assembly Replacement costs $328 on average.CarServiceEstimate2013 Chevrolet MalibuL4-2.5LService typeAxle / CV Shaft Assembly – Passenger Side Rear ReplacementEstimate$605.181978 Chevrolet MalibuV6-3.8LService typeAxle / CV Shaft Assembly – Driver Side Rear ReplacementEstimate$652.616 autres lignes
What size is the axle nut on a 2009 Malibu?
Axle Nut Length (mm): 36.72.
What is the torque specs for a axle nut?
For a double nut or jam nut system, bend the lock tab or install the set screw after the outer nut is torqued to 200 ft-lbs. For one-piece spindle nut systems, torque the nut to a minimum of 300 ft-lbs.
What size is the axle nut on a 2011 Impala?
Axle nut socket is 34mm.24 juil. 2012
What size is the axle nut on a 2012 Chevy Impala?
The axle nuts on Your 2012 Chevy Impala feature a thread size of m27-2.0.
Is it dangerous to drive with a bad wheel bearing?
Q: Is it safe to drive with a bad wheel bearing? A: No. It can, in fact, be very dangerous to drive if one of your bearings is worn out, especially since it may cause the wheel to stop while driving. Additionally, a damaged wheel bearing puts a lot of stress on the hub, the CV joint, and the transmission itself.14 mai 2019
How long can you drive on a bad wheel bearing?
To avoid this situation, it is recommended to drive at the slower speed so that your wheel stays in action a few more hours. SO, while thinking how long can you drive on a bad bearing? You should not go more than 1000 miles as it might result in some bigger issue.17 juil. 2020
Can I replace a wheel bearing myself?
Changing your own wheel bearings is considered an intermediate job that can be done at home, but will need some speciality mechanic tools. … Be sure to obtain your vehicle’s service manual and identify the type of wheel bearing your vehicle is equipped with before you begin the repair.8 avr. 2016
How much is it to replace a CV axle?
The average cost for CV axle replacement is between $1,115 and $1,151. Labor costs are estimated between $135 and $170 while parts are priced at $981. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
What happens if you over tighten axle nut?
An axle nut that is too tight will put too much preload on the hub bearings thus diminishing their life expectancy.12 nov. 2013
Should I torque axle nut?
What is the torque setting for a wheel bearing?
Generally, jam nuts less than 2-5/8″ should be torqued to 200-300 lbf-ft; nuts 2-5/8″ and over should be torqued to 250-400 lbf-ft. See chart for exact torque specification. The final step is to use a dial indicator to verify the end play or free movement of the tire and wheel assembly along the spindle axis.