Chevrolet Trax

How do you reset the oil light on a 2015 chevy trax?

1. Turn the Ignition ON, Don’t start the Engine.

2. PRESS the MENU BUTTON until the REMAINING OIL LIFE is displayed.

3. While the OIL LIFE is Displayed.

4. Turn Ignition OFF.

5. Turn the IGNITION ON, Don’t START the ENGINE.

6. PRESS the MENU BUTTON to display the REMAINING OIL OIL LIFE.

Contents

How do you reset the oil light on a 2015 Holden Trax?

How do you reset the oil life on a 2014 Chevy Trax?

1. Display the “Oil Life Remaining” message in the Driver Information Center.

2. Press and hold the SET/RESET button on the Driver Information Center for more than 5 seconds (on vehicles without DIC, use the TRIP reset stem for SET/RESET)

3. The oil life will change to “100%”

How do you check the oil life on a Chevy Trax?

1. Turn your key to the “ON” position without starting the vehicle. Your lights and electronic systems will turn on, but your engine should remain off.

2. Press the left arrow on your steering wheel-mounted controls. Keep going until you see “INFO.”

3. Then, press the up arrow until “OIL LIFE” is displayed.

How do you reset the oil light on a 2016 Trax?

How much oil does a 2015 Chevy Trax take?

CapacitiesFuel tank (gal / L):14 / 53Engine oil (qt / L):4.75 / 4.5Cooling system (qt / L):6.9 / 6.5

How do you reset the service light on a 2014 Holden Barina?

1. Turn the ignition on.

2. Press the menu button on the right stalk.

3. ENG will appear in top window and Set below.

4. Turn right stalk towards up arrow.

5. Oil or an Oil Can should appear with the number 0 beside it.

6. Press the Button on the end of the Stalk till it says 100.

7. Turn off the key and your done.

How do you reset the service light on a Holden Barina?

The light needs to be reset. Usually after an oil change they will reset it for you. Directions for doing yourself>>> turn off the engine, press and hold the select/reset button in the instrument panel then turn the ignition switch on. Hold the button until the indicator resets (approximately ten seconds).

What does code 89 mean on a Holden Trax?

Code 89 is to do with oil life reset. Your car is still ok to drive until you have this reset by your servicing Holden dealer.28 avr. 2018

When should I change the oil in my Chevy Trax?

At 7,500 miles, the technicians will check the engine oil. They may change the oil or fill the oil level. If the air filter needs replacing, they’ll change it.

Does Chevy Trax require synthetic oil?

The Chevy Trax uses SAE 5W-30 motor oil. Chevrolet recommends using synthetic oil whenever You need to change it for optimal performance. … This means that You will need fewer oil changes. On average You can go 7,500 miles between changes with synthetic compared to the 3,500 to 5,000 miles with conventional.

What kind of oil goes in a 2015 Chevy Trax?

SAE 5W-30

Does 2015 Chevy Trax require synthetic oil?

2 quarts of SAE 5W-30 full synthetic motor oil. … In its absence, it’s possible to substitute SAE 5W-40 over short periods of time.

How much antifreeze does a 2015 Chevy Trax hold?

Engine lubricant oil capacity:4.5 liter / 4.8 U.S. qt / 4 imp. qtEngine coolant capacity:6.5 liter / 6.9 U.S. qt / 5.7 imp. qtFuel tank capacity:53 liter / 14 U.S. gal / 11.6 imp. galBattery capacity (Ah):702 autres lignes

How do I reset my Holden Barina Code 89?

it means its due for service. If u wanna get rid of it without servicing the vehicle then as you start the car simultaneously push the ODOMETER reset button on the dash and it will wipe it.

See also:   What is wrong with chevrolet trax?
Back to top button

Adblock Detected

Please disable your ad blocker to be able to see the content of the page. For an independent site with free content, it is literally a matter of life and death to have ads. Thank you for your understanding!