First, go to the driver’s side of Your vehicle, and insert the key into the lock. Turn the lock to the right, or to the unlock position. Hold this position and count for 25 to 40 seconds. Doing this will bypass the anti-theft system.
People ask also, how do I turn off the anti-theft system on my Ford Explorer? To disable anti theft then get in vehicle and close the door. Put key in ignition and turn from off to run 8 times. On the eighth time leave in on position and the theft light will turn off.
Likewise, how do I bypass Ford anti-theft system? Locate the override button on the alarm box, beneath the driver’s side of the dashboard. Press the button and hold it in until the alarm beeps one time. The LED light for the alarm should stop blinking, indicating the antitheft system is disabled.
Also, how do you bypass the anti-theft system on a 2002 Ford Explorer? To begin, turn the key in the ignition as if You were trying to start the engine. The engine won’t start since the anti-theft system has been activated. Allow the key to fall back into the ON position so the dashboard lights and radio still work. Leave the key like this for at least 10 minutes.
Also know, how do I get my car out of anti-theft mode? Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.Allow the driver’s door to be locked for at least 30 seconds, then use the key in the door cylinder to unlock it. This should clear anything that is wrong with the alarm system.
How do I permanently disable anti theft system?
Turn the key to unlock your car door, but don’t release it. Hold the key in this position for 20 to 30 seconds. This lets the system know you have the correct key, and it can allow you to bypass the alarm system. Some vehicles recognize the key simply by turning the key back and forth in the door lock key cylinder.
How do you fix Anti theft system?
- Step 1: Check your key fob battery.
- Step 2: Check your door lock cylinder.
- Step 3: Check that you are using the proper key to start your car.
- Step 1: Check for the anti-theft light.
- Step 2: Turn the ignition to the “on” position.
- Step 3: Check the anti-theft light again.
Where is the anti theft fuse located?
Where is the fuse for the anti theft system? It is usually located on the dashboard by the driver’s door, in front of your left knee. You may find the alarm fuse in this fuse box. If you do not find an alarm fuse inside of the car, look in the fuse box under the hood on the driver’s side.
How do I get my 2001 Ford Explorer out of theft mode?
Press the panic button one time. Now, go to the driver’s side of Your car, and get inside. Place Your physical key into the ignition key hole, and turn it to the on position three times in a 10 second period. Now, start the engine, and the anti-theft system should be reset.
How do I reset my Ford anti-theft system?
Turn the ignition to the off position and remove the second coded key from the ignition. After three seconds and before 20 seconds, insert the new uncoded key into the ignition. Turn the ignition to the on position and keep it on for at least 6 seconds. Remove the newly coded key from the ignition.
Is my car in anti-theft mode?
If the security or anti-theft light is flashing when you attempt to start your car, and the engine does not crank or does not start, you have an anti-theft problem.
How do I disconnect my immobilizer?
How do I get my Impala out of security mode?
To reset the security on your chevy impala attempt to start the car. If it does not start, or dies very quickly after it started, then leave the key in the ignition in the “on” position and wait 10 minutes. Make sure the security light is flashing.
Will disconnecting battery reset anti theft?
One last thing you can try if your car alarm is going off and you can’t get it to stop, but you can get under the hood is to disconnect the battery. By unplugging the battery for a few minutes, it will also reset the computer. All you have to do is disconnect the positive or negative terminal and wait.