How to program a 2004 ford explorer transponder key?

Subsequently, can I program a transponder key myself? You don’t need a professional transponder key programmer to help you program your transponder. You can do this by yourself, as long as you know the right procedure. The programming process isn’t complicated, but your type of car also determines that.

Also the question is, how do you program a key for a 2004 Ford Explorer?

Considering this, how do you program a Ford transponder key with one key?

In this regard, how do you program a Ford transponder key without the original?

1. Insert original key and turn on.
2. Wait 5 seconds or until flashing security light goes off.
3. Within 10 seconds insert new key and turn on.
4. Wait 5 seconds or until flashing security light goes off.
5. Key is now programmed.

First you will need both of the programmed keys that came with the vehicle. If you do not have both, you will not be able to program the key yourself. You will need to go to the dealer to have it done. If you have both keys, put one of the already programmed keys into the ignition.

How do you reprogram a transponder key?

1. Enter your vehicle and put the key into the ignition and turn it to the “ON” position. Leave it in for 10 minutes and 30 seconds.
2. Before 45 seconds pass, turn the key to the “OFF” position.
3. Repeat the above step by turning the key to the “OFF” position within 45 seconds.

How do you reset the door code on a 2004 Ford Explorer?

To reprogRam the keyless entry pad on a Ford Explorer, type in the factory code found in the owner’s manual. Within 5 seconds, press the 1-2 button, and enter 5 digits that are personal and simple to remember. New numbers must be pressed within 5 seconds of one another to be stored by the Explorer.

How do I reset my Ford Anti theft system?

Turn the ignition to the off position and remove the second coded key from the ignition. After three seconds and before 20 seconds, insert the new uncoded key into the ignition. Turn the ignition to the on position and keep it on for at least 6 seconds. Remove the newly coded key from the ignition.

How do you program a Ford Explorer key?

1. Shut the car doors, then open the driver-side door. Press the UNLOCK button the driver-side door.
2. Now, turn the ignition from OFF to RUN 8 times.
3. Press any button on the Ford remote to program it.
4. Have more than one key fob?
5. Lastly, turn the ignition OFF.

How do I get a Ford key code?

1. Close the car doors, then open the driver-side door. Press the UNLOCK button on the driver-side door.
2. Next, turn the ignition from OFF to RUN 8 times.
3. Press any button on the Ford key fob to be programmed.
4. Have a second remote Ford key fob?
5. Finally, turn the ignition to OFF.

How do I reset MyKey without master key?

How do I program a new chip key?

1. Insert the key into the ignition, and turn it to the on position.
2. Leave the key in this position for 10 minutes and 30 seconds, and then turn it off.
3. Turn the key back on, and wait for additional 10 minutes and 30 seconds before turning it off again.
4. Repeat the process for a third time.

Can you bypass transponder key?

While it is possible to bypass your car’s immobilizer, it is not recommended. Doing so will leave your car vulnerable to theft and vandalism, since this important feature will no longer be active.

How much does it cost to program a transponder key?

Transponder key programming starts at $50 – $75. This includes keys for GM, Ford, Dodge, Honda, Toyota, Nissan. Remote or fob programming starts at $65.

Is there anyway to bypass a transponder key?

There is more than one way to bypass a transponder key. If you have some skills with electronics, you may consider permanently rewiring your ignition. Purchasing a bypass kit for your vehicle can give you a completely keyless vehicle. … Glue the transponder head to the inside and replace.