How to reset my 2002 ford explorer?

Also, where is the reset button on a Ford Explorer? To reset the fuel light on a ford explorer you will need to access the fuel reset switch which is located in the glove box or in the foot well of the passenger seat area, press that switch and the fuel system will be reset.

Also know, how do I get my 2002 Ford Explorer out of theft mode? To disable anti theft then get in vehicle and close the door. Put key in ignition and turn from off to run 8 times. On the eighth time leave in on position and the theft light will turn off.

Likewise, how do you reset a PCM Ford Explorer?

1. Open the hood of the Ford. Loosen the lock nut located on the negative battery cable connector with a socket and ratchet.
2. Wait for 20 minutes while the PCM bleeds off the electricity it stores for backup power. Once the power drains from the PCM, it resets.

People ask also, how do I get my 2001 Ford Explorer out of theft mode? Press the panic button one time. Now, go to the driver’s side of Your car, and get inside. Place Your physical key into the ignition key hole, and turn it to the on position three times in a 10 second period. Now, start the engine, and the anti-theft system should be reset.The first way is to connect an OBD-II scan tool and clear the trouble codes, so long as they are not permanent codes. Another is to disconnect the battery for at least 10 to 15 minutes. Once the power is reconnected, the light should have reset.

How do I reset my Ford Explorer screen?

Where is the reset button on a 2002 Ford Explorer?

How do I get my car out of anti-theft mode?

Step 1: Insert the key into the door lock. Use the side door on the driver’s side and the physical key even if there is a keyless entry system on the car. Step 2: Turn the vehicle key to unlock the car door without releasing it. Hold the key for 30 seconds in the position.

How do I reset my Ford anti-theft system?

Turn the ignition to the off position and remove the second coded key from the ignition. After three seconds and before 20 seconds, insert the new uncoded key into the ignition. Turn the ignition to the on position and keep it on for at least 6 seconds. Remove the newly coded key from the ignition.

How do you diagnose a bad PCM?

1. Your “check engine” light is on.
2. Other warning lights may be on, including traction control and ABS.
3. You lose fuel economy for no apparent reason.
4. Your car stutters when starting, requires multiple attempts, or won’t start at all.
5. Stuttering or stalling during idling.

How do you reset the PCM?

1. Open the hood of the vehicle.
2. Disconnect the negative battery cable from the battery. Use a wrench to loosen the lock nut, and pull the cable off. This cuts the power to the PCM. Wait for five minutes.

How do you reset a transmission control module?

1. Step 1: Turning Key Position.
2. Step 2: Press gas pedal.
3. Step 3: Keep Waiting.
4. Step 4: Turning the Key Off.
5. Step 5: Releasing Gas Pedal.
6. Step 6: Wait Again.
7. Step 7: Ready.
8. Identification.

How do I turn off Ford anti-theft system?

Locate the override button on the alarm box, beneath the driver’s side of the dashboard. Press the button and hold it in until the alarm beeps one time. The LED light for the alarm should stop blinking, indicating the antitheft system is disabled.

How do you bypass the anti-theft system on a 2000 Ford Explorer?

Allow the driver’s door to be locked for at least 30 seconds, then use the key in the door cylinder to unlock it. This should clear anything that is wrong with the alarm system.

How do I bypass PATS system?

Yes, there is a simple way to bypass the pats system on your own. All you need is the transponder key to trick the system. By having the transponder key, you can remove the chip inside the key and glue it to the ignition and use any key that matches the original to start up the engine.