Also, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.
People ask also, how do you reset the oil light on a 2007 Ford Explorer?
- Press the SETUP button until the display reads “Press Reset To Begin System Check”
- Press the RESET button to display “Hold Reset If New Oil”
- Press and hold the RESET button for 2 seconds and release.
- The oil life is now set to 100%
Also know, how do you reset the oil change light on a 2009 Ford Explorer?
Likewise, how do I reset my oil change light?
- Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
- Disconnect the negative battery terminal.
- Wrap the negative clamp in a towel.
- Leave the negative battery cable off for a minimum of five minutes.
Contents
How do you reset the oil life on a 2007 Ford Sport Trac?
Enter SYSTEM CHECK to display “OIL XXX% OIL LIFE OK”. Press RESET control to display “HOLD RESET IF NEW OIL”. Press and hold the RESET control for more than 2 seconds. Oil life is set to 100% and “OIL CHANGE SET TO 100%” is displayed.
What does the wrench light mean on a 2007 Ford Explorer?
The wrench light on a 2007 Ford Explorer means that it is time for a service on the vehicle. Usually it will be something simple like an oil change, but could be more involved like a transmission fluid change. It is impertinent to always keep up on the maintenance with Your vehicle.
How much oil does a 2007 Ford Explorer take?
Capacity: 5 quarts (with filter)When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase.
How do you reset the oil change light on a 2010 Ford Explorer?
- Press and hold the SELECT/RESET stem for more than two seconds. Oil life is set to 100% and OIL LIFE SET TO 100% is displayed.
- Once OIL LIFE SET TO 100% is displayed, release, press and hold the.
- After setting the oil life start value, press the SELECT/RESET stem.
How do you reset the oil life on a 2011 Ford Explorer?
- Switch the ignition over to the on position.
- Go to the SETTINGS menu.
- Scroll and select VEHICLE.
- Scroll down to OIL LIFE RESET.
- Press and hold the OK button.
- Shut the vehicle off and then start it back up and check the oil change light should be gone.
What does the wrench light mean on a 2010 Ford Explorer?
If You see the wrench light turn on in the dash of Your 2010 Ford Explorer this means that Your ECU has detected a fault. I recommend getting off the road as soon as possible because continuing to drive can cause more damage to Your SUV.
Why is my change oil light still on?
If your oil light stays on even after changing your engine oil, you’re going to want to check the sensor first to rule out a malfunctioning sensor as the cause. Dirt and other particles can make their way into the oil pump, causing the sensor to falsely identify oil issues. … The next common cause is low oil pressure.
Why is my engine light on after oil change?
These lights can signal something serious or something as simple as a loose gas cap. … Oil changes are essential maintenance for your car but it won’t do anything that could trigger your check engine light to come on. If you notice the light after an oil change, something else is wrong.
Why does my change oil light keep coming on?
When the oil light on your dashboard comes on, it might mean your vehicle has low oil pressure. This drop in oil pressure could be a sign of a few things: you are low on oil, your oil is dirty, or you have an oil leak.
To reset the fuel light on a ford explorer you will need to access the fuel reset switch which is located in the glove box or in the foot well of the passenger seat area, press that switch and the fuel system will be reset.