How to reset oil change message on 2010 ford explorer?

1. Get in the car and turn key to the on position.
2. Go to the SETUP MENU HOLD RESET screen.
3. Press and hold the SELECT/RESET button.
4. Enter to the RESET FOR SYSTEM CHECK menu.
5. Scroll to OIL LIFE.
6. Hold down the SELECT/RESET button.

Also know, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.

People ask also, how do I reset my messages after oil change?

1. Press and hold the reset button.
2. Turn the ignition back to the ON position while holding the reset button.
3. Watch the oil change or maintenance light carefully.
4. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.

Likewise, how do you reset the change oil engine oil light on a Ford Explorer 2011?

1. Switch the ignition over to the on position.
2. Go to the SETTINGS menu.
3. Scroll and select VEHICLE.
4. Scroll down to OIL LIFE RESET.
5. Press and hold the OK button.
6. Shut the vehicle off and then start it back up and check the oil change light should be gone.

Also, how do I reset my Ford Explorer?

1. Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
2. Disconnect the negative battery terminal.
3. Wrap the negative clamp in a towel.
4. Leave the negative battery cable off for a minimum of five minutes.

How do you reset car sensors?

How do I reset my warning light?

1. Open the hood of your vehicle.
2. Loosen the nut that holds the negative terminal to the battery with the pliers.
3. Completely remove the cable from the negative battery terminal.
4. Leave the battery disconnected for 10 minutes to ensure that the computer is fully reset.

How do I reset my service light?

How much oil does a 2011 Explorer take?

Capacity: 6 quarts (with filter)After refill check oil level.

How do you clear the code on a Ford Explorer?

The first way is to connect an OBD-II scan tool and clear the trouble codes, so long as they are not permanent codes. Another is to disconnect the battery for at least 10 to 15 minutes. Once the power is reconnected, the light should have reset.

Where is the reset button on a Ford Explorer?

To reset the fuel light on a ford explorer you will need to access the fuel reset switch which is located in the glove box or in the foot well of the passenger seat area, press that switch and the fuel system will be reset.

Why has my Ford Sync stopped working?

Reset Connection In Sync On your phone, turn Bluetooth Off, then On. … On SYNC, turn Bluetooth Off, then On. Press the Phone button > scroll to System Settings > Press OK > scroll to Bluetooth Devices > Press OK > select Off > select On. If this does not work, continue to steps 3 and 4.

How do I reset my oil life monitor?

1. Turn ignition switch to ON or RUN position with engine off.
2. Depress accelerator pedal slowly to wide open throttle 3 times within 5 seconds.
3. If CHANGE ENG OIL light flashes for 5 seconds, oil life monitor is reset.

How do I reset my Ford app?

Delete FordPass App from your phone and restart your phone. Master Reset Sync 3 (Settings, General, Scroll down to ‘Master Reset’, continue) Wait a good 5 minutes after the reset is complete for the system to settle. Ensure that remote connectivity is set to enabled in settings->fordpass app.

What can you use FordPass points for?

Redeeming Points FordPass Rewards Points can be redeemed for any qualifying transaction at any participating dealership. A member may also redeem Points toward the purchase of a new vehicle at a participating dealership.