- Get in the car and turn key to the on position.
- Go to the SETUP MENU HOLD RESET screen.
- Press and hold the SELECT/RESET button.
- Enter to the RESET FOR SYSTEM CHECK menu.
- Scroll to OIL LIFE.
- Hold down the SELECT/RESET button.
Also know, how do you reset the oil change light on a 2007 Ford Explorer?
- Press the SETUP button until the display reads “Press Reset To Begin System Check”
- Press the RESET button to display “Hold Reset If New Oil”
- Press and hold the RESET button for 2 seconds and release.
- The oil life is now set to 100%
People ask also, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.
Also, how do you reset the oil change light on a 2006 Ford Explorer?
- Locate the “TRIP/RESET” button on your vehicle’s control switch. Press and hold the “TRIP/RESET” button to select the “SYSTEM CHECK” option.
- Depress the “TRIP/RESET” button then select “OIL LIFE RESET.” The message display will show “HOLD RESET IF NEW OIL.”
Likewise, what does the wrench light mean on a 2007 Ford Explorer? The wrench light on a 2007 Ford Explorer means that it is time for a service on the vehicle. Usually it will be something simple like an oil change, but could be more involved like a transmission fluid change. It is impertinent to always keep up on the maintenance with Your vehicle.
- Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
- Disconnect the negative battery terminal.
- Wrap the negative clamp in a towel.
- Leave the negative battery cable off for a minimum of five minutes.
Contents
How do I reset my oil change light?
How do you reset the oil change light on a 2008 Ford Explorer?
Turn the ignition to the “RUN” position. Enter “SYSTEM CHECK” menu and “OIL % OIL LIFE OK” will be displayed. Press “RESET” button, “HOLD RESET IF NEW OIL” will be displayed. Press and hold the “RESET” button for more than 2 seconds.
How do I reset my 2006 Ford Explorer?
What does the wrench light mean on a 2006 Ford Explorer?
The 2006 Ford Explorer wrench indicator light means you have a concern in the fly by wire throttle actuation. You no longer have a cable, but a computer controls the throttle for speed opening or a trans concern. The most common problem is the throttle position sensor on the throttle body is bad.
What kind of oil does a 2007 Ford Explorer take?
The 4.0L V6 SOHC engine for the 2007 Ford Explorer needs 5 quarts of 5W30 synthetic oil while the 4.6L V8 engine option takes 6.3 quarts of 5W20 synthetic oil.
Can you drive with wrench light on?
It is suggested that you have your car towed into a mechanic’s garage, or, if you are one of the lucky few who still have your car on and able to drive, you drive your vehicle to a garage immediately. It is unsafe to drive with this light on for long as it may stall and won’t come back on at any given moment.
Is it safe to drive with wrench light on?
It is not safe to drive. The wrench light indicates something is wrong with your power train. When this light comes on, it means that your oil levels are low. You want to get that checked out fairly soon because ignoring it could damage your vehicle a lot.
What does the wrench symbol mean on a Ford?
The wrench warning light on Ford vehicles is the powertrain malfunction indicator light. When it illuminates, it means that the computer has detected an issue with your vehicle’s powertrain or four-wheel-drive system.
To reset the fuel light on a ford explorer you will need to access the fuel reset switch which is located in the glove box or in the foot well of the passenger seat area, press that switch and the fuel system will be reset.
How do you clear the code on a Ford Explorer?
The first way is to connect an OBD-II scan tool and clear the trouble codes, so long as they are not permanent codes. Another is to disconnect the battery for at least 10 to 15 minutes. Once the power is reconnected, the light should have reset.