Also know, how do you reset the oil life on a 2007 Ford Explorer?
- Press the SETUP button until the display reads “Press Reset To Begin System Check”
- Press the RESET button to display “Hold Reset If New Oil”
- Press and hold the RESET button for 2 seconds and release.
- The oil life is now set to 100%
Likewise, how do you reset the oil change light on a Ford Explorer? Turn the ignition to the ON position. Do not start the engine. Press and release the “Select/Reset” stem button on the instrument panel to toggle the options until the “Hold Reset For Setup Menu” option appears. Press “Select/Reset” to toggle the options until the “Hold Reset if New Oil” option appears.
People ask also, how do you reset the oil life on a 2006 Ford Explorer? Depress the “TRIP/RESET” button then select “OIL LIFE RESET.” The message display will show “HOLD RESET IF NEW OIL.”Press and hold the “TRIP/RESET” button for more than two seconds to reset the engine oil life. Once the procedure has been completed, “OIL LIFE SET TO 100%” will be displayed.
Also, how do you reset the oil life on a 2008 Ford Explorer? Turn the ignition to the “RUN” position. Enter “SYSTEM CHECK” menu and “OIL % OIL LIFE OK” will be displayed. Press “RESET” button, “HOLD RESET IF NEW OIL” will be displayed. Press and hold the “RESET” button for more than 2 seconds.Capacity: 5 quarts (with filter)When refilling, remove dipstick to provide adequate venting and allow oil to flow into crankcase.
What kind of oil does a 2007 Ford Explorer take?
The 4.0L V6 SOHC engine for the 2007 Ford Explorer needs 5 quarts of 5W30 synthetic oil while the 4.6L V8 engine option takes 6.3 quarts of 5W20 synthetic oil.
How do I reset my Ford Explorer?
- Open the hood: release the primary latch by pulling the release lever under the steering wheel near the floor board.
- Disconnect the negative battery terminal.
- Wrap the negative clamp in a towel.
- Leave the negative battery cable off for a minimum of five minutes.
How do I reset my oil change light?
What does the wrench light mean on a 2007 Ford Explorer?
The wrench light on a 2007 Ford Explorer means that it is time for a service on the vehicle. Usually it will be something simple like an oil change, but could be more involved like a transmission fluid change. It is impertinent to always keep up on the maintenance with Your vehicle.
How do you reset the oil life on a 2007 Ford Sport Trac?
What does the wrench light mean on a 2006 Ford Explorer?
The 2006 Ford Explorer wrench indicator light means you have a concern in the fly by wire throttle actuation. You no longer have a cable, but a computer controls the throttle for speed opening or a trans concern. The most common problem is the throttle position sensor on the throttle body is bad.
What kind of oil does a 2008 Ford Explorer take?
Ford recommends 5 quarts of 5W30 synthetic formulated oil for the 4.0L V6 SOHC engine in the 2008 Ford Explorer. The 4.6L V8 engine option for the 2008 Explorer uses 6.3 quarts of 5W20 synthetic oil.
How do you reset the oil light on a 2009 Ford Explorer?
Can 5w30 be used instead of 5w20?
Can You Use 5W-30 Instead of 5W-20? In theory, yes, you can switch from using 5W-20 to the 5W-30 because they have similar viscosity ratings. In fact, often, when you take your car to a mechanic for an oil change, they’ll put the 30 instead of the 20 because it’s thicker.
How often does a Ford Explorer need an oil change?
Ford recommends getting your 2021 Ford Explorer oil & filter replenished every 3,000-5,000 miles for conventional oil. Synthetic oil frequently should be replenished every 7,500 – 10,000 miles.