8 rear end width iS59 11/44 inches. The Ford 8.8 is an automotive axle manufactured by Ford Motor Company at the Sterling Axle Plant in Sterling Heights, MI. It was first used in the model year 1983 Ford trucks. The axle was developed to replace the Ford 9-inch axle.
Similarly, which Ford Explorers have the 8.8 rear end?
- 1986-2014 Ford Mustang.
- 1982-2012 Ford F-150.
- 1982-1996 Ford Bronco.
- 2001-2005 Ford Explorer Sport Trac.
- 1991-2011 Ford Ranger 4.0L models.
- 1991-2001 Ford Explorer (Solid axle)
- 1985-2011 Ford Panther platform vehicles.
- 2012-Present Ford F-150 (Super 8.8, depending on engine and other options)
Also the question is, how do I know if my Ford Explorer is 8.8 rear end? You can identify the Ford 8.8-inch rear by its rear cover. It has a thin metal or plastic 10-bolt cover, and the bolts are 7/16-inch thread. The cover is not quite square, measuring about 101/2 inches high by 11 inches long. The 8.8-inch pinion shaft is 15/8 inches and has 30 splines.
Beside above, how do I narrow my rear end Ford Explorer?
Also, how thick is a Ford 8.8 axle tube? Tube thickness: . 250″ (some are . 188″!) Ring gear diameter: 8.800″.
Contents
How much power will a Ford 8.8 handle?
Registered. 8.8 is fine up to 1,200hp or so. just weld the tubes, build a brace off the center section to the tubes, and weld 9in ends on it for the desired width.
How do I know if my Ford 8.8 is a limited slip?
There should be a tag on the diff. On bottom it will read 4 L 10. That is 4.10 limited slip.
Are all Ford 8.8 carriers the same?
Moderator Emeritus. The gears are all the same for Ford 8.8s. The carriers usually come in two different sizes, depending on gear ratio. The spider gears must match your axle spline count as that’s where they attach to the carrier.
What year did the Ford Explorer get rear disc brakes?
Increasingly popular in recent years have been the 1991-1994 Ford Explorer and 1998-and-up LS1-powered, F-body GM rear-disc systems.
How do I know what Ford rear end I have?
What Mustangs have 8.8 rear end?
From 1986-2010 the Ford Mustang 8.8 rear end went into all V8 Mustangs (5.0L, 4.6L and 5.4L) and the Ford 7.5” rear end went into all 4 cylinder (2.3L) and V6 Mustangs (3.8L). The 99-01 and the 03-04 Mustang SVT Cobras were equipped with an Independent Rear Suspension (IRS) that used the Ford 8.8” differential.
How do you narrow a 10 bolt rear end?
USA. Dave, You can narrow a 10 bolt by getting a donor rear (8 3/4 Mopar works good) and narrow the donor axles and put the chevy spline on the end. Then use the donor axle housing ends, brakes, etc and you have a much stronger rear and bigger brakes.
Are all Ford 8.8 rear ends the same?
First appearing in 1977, the 8.8 is found in almost all Ford V8 cars from ’86 on, and in V6 Rangers and Explorers. There are 24 different Fords that offered the 8.8 rear axle. … The 31-spline axles (1.29 inches in diameter) are more desirable but far less common.
How do you shorten rear axle housing?
How thick is an axle housing?
0.250″ wall thickness.