1. Turn the ignition switch OFF, and wait for ten seconds.
2. Connect the SCS service connector to the MES connector.
3. Turn the ignition switch ON (II).
4. The SRS indicator light comes on for about six seconds.
5. The SRS indicator light comes on again.
6. The SRS indicator light goes off.
Contents
What would cause the SRS light to come on?
If the SRS light stays on or starts flashing on and off, you may have a problem with the airbags themselves, a loose wire, a faulty seat belt buckle, or a problem with the Engine Control Unit (ECU) that is causing the airbag warning light to stay on.
What does the SRS light mean on a Honda Accord?
The SRS, or supplemental restraint system, on your Honda Accord is responsible for deploying the airbag in the event of an accident. If this system is malfunctioning, the airbag may not deploy properly during an accident. … The yellow “SRS” light on the dash will light up, indicating a problem with the system.
How do I reset my Honda SRS light?
1. There is a yellow plug under the dash plugged into the fuse panel.
2. Turn the ignition key to the “ON” (II) position.
3. When the SRS light comes back on plug the jumper wire back in within 4 seconds the light will blink twice and go out.
4. Unplug the jumper and turn the ignition key off.
Can you drive with the SRS light on?
While you can certainly drive while your SRS light is on, it isn’t safe. You should get your vehicle to a service center as soon as possible so that a technician can inspect your SRS computer.13 avr. 2020
How much does it cost to fix SRS light?
What is typical cost to resolve an illuminated Supplemental Restraint System (SRS) Warning Light? Expect to pay between $100 to $200 for the initial diagnostic. In this instance, look for reputation versus cost, so do not shop just on price.
How do I fix my SRS light on my Mitsubishi?
1. Plug the Mitsubishi airbag scanner into the OBD2 port under the dashboard, driver’s side.
2. Turn on the ignition and allow the scanner to power on.
3. Select your Mitsubishi model and year.
4. Select SRS / Airbag Control unit from the main menu.
5. Select Read Fault Codes.
Will disconnecting the battery reset the airbag light?
Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. … Remove the terminal clamp and leave it disconnected for 5-10 seconds to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.10 avr. 2020
How do I fix the SRS light on my Honda Accord?
1. Locate the Memory Erase Signal (MES) plug.
2. Disconnect the MES plug from its socket.
3. Strip each end of the speaker wires.
4. Hold the ends of both wires together, and turn on the ignition.
5. Hold the stripped ends of both wires together again.
6. Turn off the ignition to start your car as normal.
What is SRS fuse?
Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block. The SRS light is a warning light for your supplemental restraint system (airbags). An SRS light means that there is a problem in the system. … The fuse will not activate the airbags.23 jui. 2020
What SRS means?
Supplemental Restraint System
How does Honda diagnose SRS light?
If your Honda airbag light remains on, it most likely means that the Supplemental Restraint System (SRS) has detected a problem with the airbag system. When your Honda airbag system functions properly, the airbag light comes on when you turn on the ignition but should turn off once you start the engine.31 déc. 2020
Why is my SRS light on in my Honda Civic?
This light indicates that a fault has been detected and the airbags may not deploy or deploy properly in an accident. The SRS warning stands for Supplemental Restraint System. It supplements the primary restraint system, the seatbelts.
What is SRS code for Honda?
The secondary restraint system, or SRS, is a safety system in your Honda that controls the airbags, among other things.
How do I fix my SRS light?
1. Put the key into the ignition and turn the switch to the “on” position.
2. Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
3. Repeat Steps 1 and 2 two more times.