How to reset check engine light 2012 hyundai elantra?

To reset the check engine light in your 2017 hyundai elantra vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.

How do you reset the check engine light on a 2012?

How do you reset the check engine light on a Hyundai?

1. Locate the OBD-II port.
2. Plug your OBD2 scanner into the OBD-II 16-pin port.
3. Turn the key on.
4. The scanner turns on.
5. Read fault codes.
6. Fix the problems you found in step five, reconnect the scanner, and select Clear Fault codes.

How do I reset my 2012 Hyundai Elantra?

To reset the oil level warning or maintenance light in your 2012 hyundai elantra vehicle, turn the ignition key to the “on” position and depress the gas pedal slowly three times. Release and start your vehicle and oil light should indicate a reset.

How do you reset the check engine light on a 2013 Hyundai Elantra?

How do you reset the check engine light on a 2012 Hyundai Sonata?

Another way that You can reset the check engine light on the vehicle is to unplug the battery, wait for about 20 minutes and then plug it back in. If neither of those work then You will have to use an electronic scan tool to find the problem and fix the issue.

Why is my Hyundai check engine light on?

Why is the Check Engine light on in my Hyundai? … Your check engine light can signal different problems. It could mean a loose or missing gas cap, faulty oxygen sensor, under performing catalytic converter, faulty mass air-flow sensor or misfire in a cylinder.

Can you reset check engine light without disconnecting battery?

Can you reset the check engine light without disconnecting the battery? You can reset the check engine light without disconnecting the battery by using an OBD2 scanner. If you drive long enough after fixing the problem, most car models’ check engine light will go away by itself.

Is there a way to reset the check engine light?

Turning the Ignition On and Off The on-off method is the equivalent fix for a vehicle’s check engine light. It forces the computer to refresh its saved state through a reboot. Simply place your key into the ignition and turn it on for 1-2 seconds, then turn it off for 1-2 seconds. Repeat this step three or four times.

How do you reset the check engine light on a Nissan Sentra?

1. Open the driver’s side door and get into the drivers seat.
2. Insert the key into the ignition and turn it a quarter turn so the ignition turns on, but the engine doesn’t start.
3. Step on the gas pedal and quickly release it.
4. Wait 10 seconds.

How do I reset my car without disconnecting the battery?

1. 3.1 Step 1: Open the hood and disconnect the battery.
2. 3.2 Step 2: Locate the car’s fuse box and remove the fuse.
3. 3.3 Step 3: Reinstall the fuse and reconnect the battery terminal.
4. 3.4 Step 4: Start the vehicle and perform a test run.

How do I reset my Hyundai Elantra?

How do you reset the check engine light on a Hyundai Veloster?

To reset the check engine light in your 2013 hyundai veloster vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.

Where is the TPMS reset button located on a 2013 hyundai elantra?

2013 Hyundai Elantra The Tpms reset button is underneath the steering wheel in a 2012 Hyundai Elantra. However, if you want to locate the Tpms reset button in a Hyundai Elantra 2013, you will find it to the right of the steering wheel.

Can Autozone reset check engine light?

Wondering if the local Autozone can turn off a check engine light? The answer is yes, but… there are a couple things to remember: Local auto parts stores will typically offer to read your codes for free, but not all locations will clear the light due to liability issues.