To reset the check engine light in your 2017 hyundai elantra vehicle, try disconnecting the battery cables for 10-15 minutes and then reconnecting them, or turn your ignition key to the “on” and then “off” position twice, followed by starting the engine and the light should disappear.
Contents
How do you reset the check engine light on a Hyundai?
- Locate the OBD-II port.
- Plug your OBD2 scanner into the OBD-II 16-pin port.
- Turn the key on.
- The scanner turns on.
- Read fault codes.
- Fix the problems you found in step five, reconnect the scanner, and select Clear Fault codes.
How do I turn my check engine light off?
How do you reset the check engine light on a 2013 Hyundai Elantra?
Can I turn off my own check engine light?
Continue Driving and Let it Clear on its Own When you fix a problem that was causing the check engine light, it may take a while for the computer system to refresh its ‘present state. ‘ Once it does, it will recognize the diagnostic is no longer flagging an issue and the light will go off.
Why is my check engine light on Hyundai Elantra?
Why is the Check Engine light on in my Hyundai? … Your check engine light can signal different problems. It could mean a loose or missing gas cap, faulty oxygen sensor, under performing catalytic converter, faulty mass air-flow sensor or misfire in a cylinder.
Can I drive with check engine light on?
The rule of thumb is that if the check engine light is flashing, you can’t keep driving the car. It’s an emergency. Often it indicates an engine misfire. If you keep driving, you will likely cause irreversible damage, mostly to the (expensive) catalytic converter.
How do you reset the check engine light with a gas pedal?
Fully depress the accelerator pedal and keep it for more than 10 seconds. Fully release the accelerator pedal (The CEL light will continue to blink). Turn ignition switch to On position and now you can start the car. The CEL light should be gone.
How do I reset my car without disconnecting the battery?
- 3.1 Step 1: Open the hood and disconnect the battery.
- 3.2 Step 2: Locate the car’s fuse box and remove the fuse.
- 3.3 Step 3: Reinstall the fuse and reconnect the battery terminal.
- 3.4 Step 4: Start the vehicle and perform a test run.
How do you turn off the check engine light on a Hyundai Sonata?
There are different ways to reset the check engine light on the 2018 Hyundai Sonata but sometimes it will just go off by itseLFAfter driving for a while. Another way that You can reset the check engine light on the vehicle is to unplug the battery, wait for about 20 minutes and then plug it back in.
Can Autozone reset check engine light?
Wondering if the local Autozone can turn off a check engine light? The answer is yes, but… there are a couple things to remember: Local auto parts stores will typically offer to read your codes for free, but not all locations will clear the light due to liability issues.
What is the most common reason for check engine light?
Replacing a faulty oxygen sensor — a sensor used to optimize a vehicle’s fuel-to-air mixture to increase gas mileage and reduce emissions — is the most common cause for a check engine light.
How do you reset the check engine light on a Hyundai Ioniq?
- Let it go off by itself.
- Turn your ignition on and off several times in a row.
- Disconnect your battery and reconnect it.
- Buy an OBD II scanner (they’re relatively inexpensive) and follow the instructions (it’s pretty easy)
Why is my engine light on?
The light could be a minor issue, such as a faulty gas cap, or it could mean something more serious, such as a misfiring engine. … The check engine light — more formally known as the malfunction indicator lamp — is a signal from the car’s engine computer that something is wrong.
Will your check engine light come on if you run out of gas?
Yes, it is entirely possible that the check engine light will come on AS you are running out of gas. After you walk to the gas station , buy a can, and walk back with a couple gallons, the car will restart. The Check Engine light will still be on for a couple of ignition cycles.
How many miles can you drive with check engine light on?
To make sure the check engine light does not reappear, it’s recommended that you drive your car 30 to 100 miles. This enables the vehicle’s “Drive Cycle” to reset, as the various sensors need time to recalibrate.