Each time Your 2012 Hyundai Sonata is serviced, the “Service Interval” settings should be reset. Press and hold the “OK” button on the right-hand side of the steering for 5 seconds, and the Service Interval will be reset to its default settings.
Furthermore, how do you reset the computer on a Hyundai Sonata? To reset the computer in a Hyundai vehicle, open the hood and use a wrench of pliers to disconnect the positive cable from the battery. Look for the fuse that says ECM on it and remove it. Keep this removed for at least three minutes to clear the vehicle’s memory.
Additionally, how do I reset my Hyundai?
Likewise, how do you reset the check engine light on a 2012 Hyundai Sonata? Another way that You can reset the check engine light on the vehicle is to unplug the battery, wait for about 20 minutes and then plug it back in. If neither of those work then You will have to use an electronic scan tool to find the problem and fix the issue.
Also, where is the reset button on a 2011 Hyundai Sonata? To reset the tpms on the 2011 hyundai sonata make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and wait ten minutes. In some cases you may need to hold the button down till the light flashes.disconnect battery, pump brake until no more lights, wait 5 min, reconnect battery, turn key to ‘ON’ (don’t start car yet) for about 1-2 min for ECU to power back up and finish resetting, key to off, start car. If car doesn’t start right away, leave key in On position and wait for another min then restart.
How do you reset your car’s computer?
How do I reset my car without disconnecting the battery?
- 3.1 Step 1: Open the hood and disconnect the battery.
- 3.2 Step 2: Locate the car’s fuse box and remove the fuse.
- 3.3 Step 3: Reinstall the fuse and reconnect the battery terminal.
- 3.4 Step 4: Start the vehicle and perform a test run.
How long does it take for a car computer to reset?
The readiness monitors will remain until the car has been driven long enough for the computer to evaluate the various system and sensors. The amount of time can vary based on the vehicle. In some cases it can take up to 100 miles for all of the computer monitors to completely reset.
How long do I have to drive my car to reset the computer?
So why is the light still on? Here’s something you probably don’t know: after clearing the car’s computer you will need to drive for about 50 to 100 miles. As you drive your car the computer will monitor all the sensors and register the results.
Why is my check engine light on Hyundai Sonata?
If the check engine light in your Hyundai Sonata starts glaring, that means that the problem needs immediate attention and your Hyundai should be brought in quickly. This blinking light usually indicates a severe engine misfire allowing unburned fuel to be dumped into the exhaust system.
Where is the obd2 port on Hyundai Sonata?
The 2013 Hyundai Sonata OBD port location can be found to the right in the driver’s side footwell near the gas and brake pedals. The OBD port will allow You to connect a diagnostic tool to the vehicle and get fault errors.
What does code P1326 mean Hyundai Sonata?
The P1326 error code showing up on the Hyundai Santa Fe Sport means there is a problem with the connecting rod bearings of the vehicle. … Make sure to have the vehicle checked by a professional as soon as possible, because continuous wear and tear of these bearing can lead to damage of the engine.
The Tpms reset button is underneath the steering wheel in a 2012 Hyundai Elantra.
To reset the tire pressure monitor or tpms system in your 2013 hyundai sonata vehicle, turn the ignition key to the “on” position and depress the tpms button, usually located under the dash, until the tpms light blinks several times.
The tire pressure monitor reset button can be found under the steering wheel.