To reset the tire pressure monitor or tpms system in your 2018 jeep grand cherokee vehicle, turn the ignition key to the “on” position and depress the tpms button, usually located under the dash, until the tpms light blinks several times.
Furthermore, where is the TPMS reset button on Jeep Cherokee? This button is usually located under the steering wheel. Now, let go of the button after the light blinks at least three times. Drive Your car for about 20 to 25 minutes for the reset to take place.
Correspondingly, where is the TPMS reset button? The TPMS reset button is usually located beneath the steering wheel. If you are unable to find it, refer to your vehicle’s owner’s manual. Inflate all tires to 3 PSI over their recommended amount, then deflate them completely. Be sure to include the spare tire, as it may have a sensor as well.
Also know, how do you reset the tire pressure light on a 2014 Jeep Cherokee?
Likewise, how do you manually reset TPMS? Starting with the vehicle off, turn your key to the “On” position, but don’t start the vehicle. Find the TPMS reset button (check your manual if you need help), and hold it until the tire pressure light blinks three times. Then, start the car and wait 20 minutes for the tire pressure light to reset.
- Drive your car at 50 mph for 10 minutes to reset the sensor.
- Find a place to park and turn off your car completely.
- Turn your key to the “On” position without turning the car back on.
- Press the TPMS reset button and hold until the light blinks three times.
- Release the button.
Contents
How do you reset the tire pressure sensor on a 2010 Jeep Grand Cherokee?
Turn the key to the “On” position, but don’t start the car. Locate the TPMS reset button under the steering wheel and press in, holding until the tire pressure light blinks three times. Start the car and wait 20 minutes for the sensor to refresh.
Can I reset the TPMS by disconnecting the battery?
Find the battery and disconnect the negative battery cable. You will need a wrench to do this. Once the battery is disconnected, turn your vehicle on and press the horn for approximately three seconds. This will drain any remaining energy stored in the vehicle’s electrical system.
Why is my TPMS not working?
TPMS problems can include any of the following: A TPMS sensor that has stopped functioning because the battery has died. A TPMS sensor that is working intermittently due to a weak or failing battery. The TPMS module is not receiving a signal from one or more sensors because of an antenna or wiring fault.
Why is my low tire pressure light on but tires are fine?
The tire sensors may be in need of a reset if the tire position on the wheel was changed. Depending on the car, this may just mean that you need to drive around for a few minutes so the tire can reset. If this doesn’t work, you may need to request a full calibration at the dealership or tire shop.
To reset the tpms on the 2010 jeep wrangler make sure the tire pressure is correct, then turn on the vehicle. Now hit the reset button that is to the right of the steering wheel and wait ten minutes. In some cases you may need to hold the button down till the light flashes.
What should the tire pressure be on my Jeep Cherokee?
Having properly inflated tires helps them last longer because they will get more even wear. The tire size for the 2018 Jeep Cherokee is Front Tire 225/55R18 and Rear Tire 225/55R18. The recommended tire pressure for both front and rear tire is 33 psi.
How do I turn off the tire pressure light?
Turn the car key to “on” but don’t start the vehicle. Press and hold the TPMS reset button until the tire pressure light blinks three times. Release the button and start the car. The light should go off within 20 minutes.
How do you reset tire sensors?
Without starting the car, turn the key to the “On” position. Press the TPMS reset button and hold it until the light blinks three times, then release it. Start the car and let it run for 20 minutes to reset the sensor. You’ll usually find the tire pressure monitor reset button beneath the steering wheel.
How do I use the TPMS reset tool?
What is a TPMS relearn tool?
Relearning. Relearning tools are used to locate new sensors. The Engine Control Unit (ECU) needs to know the location of the sensors if you have new ones installed or if you’ve installed new tires. Relearning tools also activate the sensors if they are in sleep mode.