How to get fault codes on jeep grand cherokee?

1. Pull the release lever to open the hood from inside the vehicle.
2. Open the hood and place the support rod into position to prop up the hood.
3. Remove the nut connecting the negative battery terminal to the battery, using an open end wrench.
4. Allow the computer to reset.

Also know, how do I find the engine code on a 2005 Jeep Grand Cherokee? Insert your key into the ignition slot, and turn it from ‘Off’ to ‘On’ (Do NOT start your vehicle) 3-5 times until ‘DTC REPORT’ appears in the odometer display for 2005-2010 models, or the DTC’s start displaying on 1999-2004 models. Write down all codes, starting with the letter ‘P’, and ending with 4 numbers (0-9).

Correspondingly, how do I find the error code on my Jeep Grand Cherokee?

1. Insert the key into the ignition.
2. Turn the ignition On-Off-On-Off-On within 5 seconds.
3. Record the 2-digit DTC as displayed by the flashing MIL.

As many you asked, how do I check the error code on a 2004 Jeep Grand Cherokee?

Quick Answer, how do you reset the code on a Jeep?

1. Make sure the engine is not running and key is out of the ignition.
2. Disconnect the battery terminals.
3. Wait 5 minutes.
4. Reconnect battery terminals.
5. Insert and turn the ignition key to the run position without starting.
6. All error codes are cleared and CHECK ENGINE icon disappeared.

How do you reset the computer on a Jeep Grand Cherokee?

1. Disconnect the battery by removing the positive battery cable.
2. Ground the positive cable to the negative cable for 30 seconds to erase the electric charge in the capacitors.
3. Reconnect the positive cable to the battery.
4. Turn the key to on but do not start.
5. Turn the headlights on.

How do I find the code for my 2012 Jeep Grand Cherokee?

How do I find the code for my Jeep Wrangler?

1. Insert key into the ignition.
2. Turn to “ON” position without starting the Jeep.
3. Push the key in and turn it to “OFF” and then to “ON” three times, leaving it in the “ON” position.

How do you check the codes on a Jeep TJ?

1. Turn the ignition key On – Off – On – Off – On within 5 seconds.
2. Count the number of times the check engine lamp on the dash flashes on and off. The number of flashes represents the trouble code. There is a slight pause between the flashes representing the first and second digits of the code.

How do I find my Jeep engine code?

How do you reset the check engine light on a 2017 Jeep Grand Cherokee?

To turn off the Jeep Grand Cherokee check engine light, turn the ignition switch to ON but don’t start the vehicle. Press the gas pedal 3 times within 10 seconds and turn the ignition off. Wait 10 seconds and start the engine.

How do you reset the computer on a 1999 Jeep Grand Cherokee?

Put your key in the ignition and turn it to the “ON” position. Do not start the engine. Turn on the headlights, and leave them on for 10 to 20 seconds. Then turn off the headlights.

Why is my check engine light on in my Jeep Cherokee?

If the check engine light in your Jeep Cherokee starts flashing, that means that the problem needs sudden attention and your Jeep should be brought in today. This blinking light mostly indicates a scrupulous engine misfire allowing unused fuel to be deposited into the exhaust system.

What is the DTC report on a Jeep Grand Cherokee?

A Diagnostic Trouble Code (DTC) indicates that the Powertrain Control Module (PCM) has recognized an abnormal condition in the system.

How do I reset my Jeep ECM?

1. Step 1 – Remove the positive (red) battery cable.
2. Step 2 – Ground the red cable to the negative terminal.
3. Step 3 – Reconnect the positive battery cable.
4. Step 4 – Turn on your Jeep.
5. Step 5 – Cycle the headlights.
6. Step 6 – Turn the key off and remove.