How to program a key fob to a 2004 jeep grand cherokee laredo?

1. Press and release the “lock” button in two-second intervals.
2. Turn the ignition on.
3. Press and hold the “unlock” button for up to 10 seconds.
4. Hold the “unlock” button, while pressing the “panic” button.
5. Complete the process by programming a button into the system.

Quick Answer, how do you program a key fob for a Jeep Grand Cherokee? Chrysler Key Fob Programming Press the “LOCK” button on your key fob five consecutive times, while allowing 2-second intervals between each press. Next, put your key in the ignition and turn two clicks to the “RUN” position. Hold down the “UNLOCK” button and “PANIC” button simultaneously. Release both at the same time.

Moreover, why won’t my Jeep recognize my key fob? Reasons your car won’t detect the key fob the battery inside the remote is dead. the remote itself is broken or no longer programmed to your car. the car battery is low. the keyless operation system is faulty.

Also the question is, how do I program my Jeep key with only one key?

Subsequently, does a 2004 Jeep Grand Cherokee have a chip in the key? Jeep Grand Cherokee 1998–2004 Transponder chip metal blade If your Jeep Grand Cherokee was manufactured in 1998, 1999, 2000, 2001, 2002, 2003 or 2004, your vehicle utilize a Transponder chip metal blade high security Y160-PT key. … if one of the keys is missing, the key can be reproduced by a cloning procedure.DIY Key Fob Programming Depending on the age and model of your car, you may be able to program a replacement yourself. The procedure for do-it-yourself key fob programming can vary: Some automakers provide instructions in their owner’s manuals. Information can be found in many cases on the internet.

Can you program a key fob without the original key?

You don’t need to go to a dealership to have your fob programmed but a professional locksmith IS REQUIRED if the original is not available. Absolutely, that doesn’t need a locksmith at all, dealership store can program it for free. You absolutely can.

What do I do if my key fob is not detected?

If your display does not recognize the key and shows the key fob not detected, first press UNLOCK button on the key fob. Next, press the START button with the keyfob. These cars have a slot on the left of the steering wheel where you insert the key if it is not detected.

How do I reprogram my key fob after replacing the battery?

1. STEP 1-Turn on the ignition. You should sit in the driver’s seat with both the ignition key and the key fob with all doors closed.
2. STEP 2-Press the lock button.
3. STEP 3-Turn off the ignition.
4. STEP 4-Repeat the process with other key fobs.
5. STEP 5-Restart the process.

What do I do if my key fob doesn’t work?

Bad Battery – The most common reason your key fob has stopped working is because of a dead battery. A simple swap with a fresh battery that you can find at most big box stores should do the trick to get things working again. Try opening your car door with a second key fob.

How do you bypass a key transponder?

What do I do if I lost my Jeep key?

1. First, call an automotive locksmith that offers a mobile service for Jeep cars. We can help you with that.
2. Second, tow the car to the dealer.
3. Third, order a key online and have the dealer or locksmith cut and program (if necessary) it for you.

How do I find my Jeep key code?

Turn the key in the following pattern: On-Off-On-Off-On. Grab a pen and paper and count the number times the check engine light flashes at you. It will be a code.

What year did Jeep start putting chips in the keys?

Chrysler, Dodge, Plymouth and Jeep began using transponder chip keys in 1998. Transponder based systems are standard on some models, and optional on others.

How much does it cost to replace a Jeep Grand Cherokee key?

In short, replacing a Jeep Grand Cherokee key can cost between $135 to $450.

How do I reset my Jeep security system?

To reset the Jeep Wrangler safe, use the ignition key to turn your car on and keep the red toggle switch on the alarm system. Wait until the detector is turned off and the machine emits a chirping sound. The LED light on the panel would also be turned on to show that the alarm is reset and the device is working.