Also, how do I know if my blower motor resistor is bad or blower motor?
- Fan does not work at all, so no air comes out of the vents.
- Fan only works on some speeds and not others.
- Fan only works on the highest speed.
- Fan runs all the time and can’t be controlled with the fan switch.
- You see smoke coming out of the vents.
As many you asked, what are the signs of a bad blower motor resistor? If the airflow from the vents is weak… If you try to increase the air pressure and you feel no difference in the pressure blowing, then your blower motor resistor may be failing. A damaged blower motor resistor will work on one fan speed which may not be enough to keep the inside of your car cool or warm enough.
In this regard, what happens when a blower motor resistor goes bad? If the resistor shorts or fails, it may cause the blower motor to remain stuck on one fan speed. The heating and air conditioning systems may still function at one speed, however the resistor will have to be replaced in order for full functionality to be restored.
Subsequently, why is my blower motor not working? In a situation where the motor doesn’t work on any speed, the most likely causes are: a blown power supply fuse, a bad motor ground connection, bad motor speed control module or a failed motor. On all systems, a failed blower motor is least likely. Start by checking the blower fuse and HVAC controller fuse.
- Weak airflow. This is one of the first signs of a bad blower motor that people tend to notice.
- Noises. Have you noticed any unusual noises coming from your vehicle’s HVAC system?
- Smoke or smells.
Contents
How much does it cost to replace a blower motor resistor?
Blower Motor Resistor Replacement Cost – RepairPal Estimate. Labor costs are estimated between $44 and $55 while parts are priced between $64 and $82. This range does not include taxes and fees, and does not factor in your specific vehicle or unique location. Related repairs may also be needed.
What causes a blower motor resistor to go out?
In most cases, a blower motor resistor fails due to corrosion or overheating. Sometimes, the mechanical resistance to the motor rotation causes an excessive electric current that can overheat and prematurely damage the blower motor resistor.
Can I bypass blower resistor?
In the highest speed state, the blower resistor is bypassed completely and the fan is connected directly to the car’s battery, which allows maximum current through the motor. Power to the blower motor is fed through the blower motor resistor, so if it fails or has any issues power can be cut off to the motor.
How do you test a blower motor resistor on a Jeep?
Place one lead of the Ohmmeter on terminal 1 of the resistor. Place the other lead on terminal 2 and check against specifications. If this circuit is open, showing infinity on the Ohmmeter, the blower resistor must be replaced. Move the lead from terminal 2 to terminal 3 and check this reading against specifications.
Where is the blower motor located on a Jeep Wrangler?
On a Jeep Wrangler, the blower motor is necessary to the air conditioning, heating and defrosting systems. It is located under the dashboard on the far end of the air duct on the passenger’s side. It is easy to access and can be removed in minutes.
How do you remove a Jeep TJ blower motor?
How do you test a blower control module?
How much does it cost to replace a blower motor?
Replacing a blower motor costs $450 on average with a typical range of $250 to $800. With a warranty, you might pay as little as $150 for labor alone. For high-end models, like those with large motors or access issues, you might pay as much as $2,000.
What does a bad blower motor sound like?
A defective blower motor will make a continuous sound noticeable by the passengers in the vehicle. It can manifest as a knocking, whirring, clunking, vibrating, squealing, or whining noise that persists until the blower motor is replaced.
How do I reset my blower motor?
- Step 1: Turn off the power to the furnace.
- Step 2: Remove the blower compartment cover.
- Step 3: Make sure the blower is completely cooled off.
- Step 4: Locate the reset button.
- Step 5: Press the button in (assuming that this is your issue and that the button has popped).