Unfortunately, the SRS Airbag light doesn’t reset on its own. Even if the problem has been addressed, you will need an Airbag scanner to reset the light. Very often the light goes on because of a dying battery. But once the light is on, it will stay on even when you install a new battery, until you manually reset it.
Also know, how do I get the SRS light off?
- Put the key into the ignition and turn the switch to the “on” position.
- Watch for the airbag light to turn on. It will stay illuminated for seven seconds and then shut itself off. After it shuts off, immediately turn the switch off and wait three seconds.
- Repeat Steps 1 and 2 two more times.
Also, what does the SRS light mean on a Mercedes? The SRS Light in your Mercedes-Benz is an acronym for “Supplement Restraint System.” So, what does this mean? Your SRS light coming on and staying on is indicating that there is an issue with your Mercedes-Benz airbags and components that are related to and part of the SRS system.
Likewise, can you disable an airbag light? Luckily, you can reset and turn off your airbag light. You can also recheck the connectors in case the light fails to turn off. Turning off the airbag light yourself can save you a trip to your car dealer.
People ask also, what would cause the SRS light to come on? If the SRS light stays on or starts flashing on and off, you may have a problem with the airbags themselves, a loose wire, a faulty seat belt buckle, or a problem with the Engine Control Unit (ECU) that is causing the airbag warning light to stay on.
Is there a fuse for the SRS light?
The fuse block is on the driver’s side of the engine compartment. Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block.
Will disconnecting the battery reset the airbag light?
Often, all it takes to get rid of that pesky warning light is to reset your airbag sensor. … Remove the terminal clamp and leave it disconnected for 5-10 seconds to allow the airbag sensor to reset. Then reconnect the battery terminal and turn the vehicle on. With a bit of luck, the light will stay off.
How much does it cost to reset the airbag light?
Number 1 — Reset Airbag Light You’ll need to hire a professional to come in and examine the airbags before you continue to drive the car. This process can take several hours of time and usually costs a few hundred dollars, although depending upon the type of car it may be up to about $600.
How do I fix my SRS light on my Mitsubishi?
- Plug the Mitsubishi airbag scanner into the OBD2 port under the dashboard, driver’s side.
- Turn on the ignition and allow the scanner to power on.
- Select your Mitsubishi model and year.
- Select SRS / Airbag Control unit from the main menu.
- Select Read Fault Codes.
Can you drive with the SRS light on?
While you can certainly drive while your SRS light is on, it isn’t safe. You should get your vehicle to a service center as soon as possible so that a technician can inspect your SRS computer.
How do you reset the SRS light on a Mercedes w211?
- Locate the fuse panel cover and remove it.
- Put the key into the ignition and turn it to the “Run” position.
- Check your owner’s manual for what the codes mean.
- Unplug the scan tool and put the fuse panel cover back in place.
Will removing fuse disable airbag?
The NHTSA says that you can’t remove or disable the airbags on any registered, road-driven vehicle newer than 1996 without a waiver. … Simply pulling the airbag fuse may not disable the airbags. Many ACMs utilize an internal battery to ensure deployment even if the power is cut.
What happens if you remove SRS fuse?
Every vehicle I’ve worked on has had an airbag fuse you can remove from the fuse panel to fully disable the airbag; the repair manuals recommend pulling this fuse when doing any work in the dash area since there’s some risk of triggering the airbags to go off while you’re working, which could result in serious injury …
What happens if you disconnect an airbag sensor?
What happens if you unplug airbag module? … Disconnecting the airbag unit from the harness without unplugging the battery may trigger the airbags to deploy or may cause damage to the computer system. After disconnecting the positive battery cable, you should wait three minutes before removing the computer module.
Where is the fuse for SRS light?
The fuse block is on the driver’s side of the engine compartment. Pull out the SRS fuse. In most models, this is fuse #40, located in the lower right corner of the fuse block.