To turn on the passenger airbag in a 2019 Subaru crosstrek, press the airbag button below the radio in the center dash.
Best answer for this question, how do I activate passenger airbag? The switch for the passenger airbag (PACOS) is located on the passenger end of the instrument panel and is accessible when the passenger door is open. Check that the switch is in the required position. The remote control key’s key blade should be used to change position.
Moreover, why is my passenger airbag off light on? Your passenger airbag will turn off if your passenger is: Light enough that the weight sensor detects that someone is occupying the seat, but not heavy enough that deploying the airbag is a wise idea. The sensor believes the person sitting in this chair is too light and deploying the airbag would be unsafe for them.
Beside above, should passenger airbag light be on or off? Sensors monitor the weight (so airbag would not deploy injuring a child, or pet etc). If there is someone sitting in passenger seat, this light should be off. If its on in this case, have the person re-adjust their position & then you may need to turn car off & restart.
Subsequently, can you turn off passenger airbag Subaru? Unscrew it for the seat and unplug the electrical connector going to it. Once the sensor is replaced the light should turn off. The passenger airbag in a Subaru Legacy will turn off automatically based on weight.
Contents
How do you turn off the passenger airbag on a 2017 Subaru Outback?
It may be on the dashboard itself, in the glovebox or on the side of the dash so that you need to open the passenger door to access the switch. The switch will have two positions ‘on’ and ‘off’.
What does it mean when it says front passenger airbag enabled?
Possible Causes This message may also come up if there is a child seat on the front passenger side. If you have an adult or don’t have any passengers present but are getting any of these messages, it means a malfunction has been detected by the Weight Sensing System, also known as WSS or N2/13 control module.
What does front passenger airbag enabled mean?
The automatic front passenger front airbag shutoff is able to detect whether the front passenger seat is occupied by a person or a child restraint system. The front passenger front airbag is enabled or disabled accordingly. … Never place objects, e.g. cushions, under or behind the child restraint system.
How does a car know when someone is in the passenger seat?
When someone sits on the seat, the pressure sensor signals the occupant’s weight to the ECU. The ECU then sends that data to the airbag, which has its own control unit. … It reads the passenger’s seating position and determines if they’re wearing a seat belt.
How do you reset the passenger airbag light?
- Turn your ignition on and off.
- Restart your vehicle and do a test drive.
- Examine the passenger airbag switch.
- Inspect whether seat belts are fastened or working correctly.
- Verify that the passenger seat sensor is not applied.
- Use a scanner with an SRS or airbag light reset option.
Why must the SRS be disabled before working on or around the air bags?
To avoid serious or fatal injury on vehicles equipped with air bags, disable the SRS (supplemental restraint system) before attempting any steering wheel, steering column, airbag, seat belt tensioner, impact sensor or instrument panel component diagnosis or service.
How do I turn off my airbag driver?
- Purge the Power. The first step involved in the process of how to disable airbag system in your car is to cut off the power.
- Take Out the Fuse.
- Take Away the Dashboard Cover.
- Immobilize the Passenger Airbag.
- Remove the Steering Wheel’s Lower Panel.
- Finally, Disable the Airbag.
Is it illegal to disable airbags?
It is illegal for a mechanic to disable a bag, unless permission has been obtained for that vehicle from the National Highway Traffic Safety Administration, but it has always been legal for a car owner to do so.
How do you reset the airbag light on a Subaru?
How do you turn off the seatbelt chime in a Subaru?
Just learned this, and wanted to share for anybody who does’t know. Turn the key in the ignition to “on”, the spot just before starting the engine. Buckle and unbuckle the seatbelt 20 times within 30 seconds.