Put your key in the ignition and turn it to position one, which is the position right before starting the car. Push and hold the trip meter reset button on the dashboard, then turn the key to position two. Keep holding the odometer button for 10 seconds. The light should then flash, beep, and then go out.
Beside above, how do you turn off the maintenance required light on a Toyota RAV4 2020?
Likewise, how do you reset the maintenance required light on a 2012 Toyota RAV4?
- Turn on your car without starting.
- Make sure you are on TRIP A screen.
- Switch off the ignition.
- Hold down the ODO/TRIP button while turning the car back on.
- Keep holding it until you see zero and you’re done.
Moreover, how do you turn off the maintenance required light on a 2015 Toyota RAV4?
Also, how do I turn off the maintenance required light?
- Turn ignition switch to the ON position.
- Set the Odometer/Trip Display to TRIP A mode.
- Turn the ignition switch to the OFF position.
- Depress and HOLD the Trip Meter RESET button while turning the ignition switch to the ON position.
- The Service Maintenance Reminder Light will.
- Use your keys to turn the key to the “On” position in your Toyota Corolla, but don’t start the car.
- Locate and press and hold the “trip reset” button on the odometer.
- Then, turn the key back to “Off.”
Contents
How do I turn off the maintenance required light on my Toyota Camry?
Push and hold the dashboard odometer button and turn the key to position two. Keep holding the odometer button until the maintenance light starts to flash. You might even hear beeping noises. The light should go out.
How do you turn off the maintenance light on a Toyota 4Runner?
To reset the maintenance light on a Toyota 4Runner, you must turn the ignition switch to the “ON” position, then set the trip display to “ODO” mode, turn the ignition switch to “OFF,” then press and hold the trip “RESET” button, while turning the ignition to the “ON” position.
How do you reset the maintenance light on a 2013 Toyota Rav4?
How do you turn off the maintenance required light on a Toyota Tundra?
- Turn your key to the “On” notch, and press your trip odometer knob until “Trip A” is displayed.
- Turn your key to the “Off” notch. Press and hold the trip odometer knob.
- Wait for the system to reset.
- Release the trip odometer knob when “Trip A” is displayed again.
What does it mean when my Toyota Rav4 says maintenance required?
The icon MAINT REQD meaning is important. When the MAINT REQD light goes on it indicates that the vehicle’s scheduled maintenance is due. This service may be covered under your ToyotaCare plan if your vehicle is less than two years old.
Why does my Toyota maintenance light keep requiring maintenance?
What ‘MAINT REQD’ Means. The ‘MAINT REQD’ light comes on every 5000 miles from the last time it was reset. It in no way indicates any system malfunction; it is simply a mileage counter intended to remind the user that an oil change is necessary.
How do you reset the oil maintenance required?
Hold the Reset Button and Turn the Key Turn the ignition back to the ON position while holding the reset button. Watch the oil change or maintenance light carefully. It should start to blink. Allow the light to blink ON and OFF for a few seconds, then release the reset button and turn the ignition OFF.
How do you turn off the maintenance required light on a Toyota Tacoma?
Turn the vehicle completely off. Press and hold the “Odo/Trip” button. Continue to hold the “Odo/Trip” button while switching the ignition to “On” without starting the engine. Release the “Trip” button until the trip meter is set to all zeros.
How do you turn off the maintenance required light on a Toyota Yaris?
Press and hold the trip meter reset nob (next to your toyota yaris’s odometer). While holding the trip meter reset nob, turn the ignition to ‘on’, but do not start your toyota yaris. Hold the meter reset until the maint reqd light switches off.
How do you reset the maintenance required light on a 2010 Toyota Corolla?
Quickly push and hold the odometer button on your dashboard, then turn your key to position two. Continue to hold the odometer buttonfor around 10 seconds. The maintenance light should begin to flash, and you may hear a beeping. Then the light should go out.